How to Size a Firewood Conveyor: Lift Height, Belt Length & Incline Angles for Dump Trailers and Woodpiles

What separates a great firewood conveyor purchase from a disappointing one is discharge height at a workable angle, not the number printed next to "belt length." Sizing a firewood conveyor means working within the 25° to 28° incline limit, so you get the right lift height for your trailer and the most cord volume from a conical woodpile.

Carry this rule of thumb into every showroom or checkout page. Take the tallest sidewall you plan to clear, add about 18 inches of drop margin, and make sure the machine's rated lift covers that number while the belt holds 25° to 28° during real work. Anything steeper sends round splits tumbling backward.

Most of the math below is simple trigonometry you can do on a phone calculator. The rest is knowing how to read a spec sheet. If you are comparing a firewood conveyor for sale from any brand, these same checks apply, and we use two MechMaxx models as worked examples throughout.

Worker feeds split firewood into a red conveyor discharging into a tall dump trailer.

1. The Two Models at a Glance

Both machines come from the MechMaxx conveyor lineup, and both pair a gasoline engine with a hydraulic belt drive. The HC2016 is the lighter, more maneuverable one. The HC2320 is taller and wider, built for heavy duty.

Spec

MechMaxx HC2016

MechMaxx HC2320

Engine

7HP 212cc, single cylinder, 4-stroke, air-cooled OHV

9HP 270cc with recoil start

Belt length

236 in (19.6 ft)

276 in (23 ft)

Belt width

16 in

19.7 in

Max discharge height

124 in (10.3 ft)

180 in (15 ft)

Min discharge height

60 in (5 ft)

8 ft

Drive

Hydraulic, 5.7 GPM single-stage pump

Hydraulic, with hydraulic height adjustment

Best fit

Residential and small-lot stacking, standard trailers

High stake beds, big commercial piles

2. The Core Sizing Mistake: Belt Length vs. Actual Lift Height

Plenty of buyers see a 20-foot belt and assume a 20-foot reach. A belt runs along a slope, while discharge height is the vertical rise at the top of that slope. The sine of your working angle connects the two.

The shortcut is easy to remember. At 28°, every foot of vertical rise needs roughly 2.1 feet of belt run. At 25°, it needs about 2.4 feet. A 19.6-foot belt working at a sensible firewood angle therefore puts its discharge roughly 8 to 9 feet in the air before frame and pivot height are counted. That is why the MechMaxx HC2016 firewood conveyor lists a 236-inch belt beside a 124-inch maximum discharge height. Two different measurements, two different jobs.

The same logic explains why a bigger belt is not automatically a better buy. Shop on belt length alone and you may end up with a machine that looks long in the photos but cannot clear a tall sidewall without steepening the slope past what the wood will tolerate. Start with rated discharge height, then check that the belt gives you a gentle enough run to reach it.

Minimum discharge height matters too, and buyers often skip it. The HC2016 lowers to 60 inches, which suits a long windrow of low-stacked splits or a small trailer. The HC2320 bottoms out at 8 feet, so it is a tall-pile, tall-truck machine.

Diagram comparing conveyor belt run along a 25–28 degree slope with vertical discharge height.

3. The Physics of the 25° to 28° Incline Window

Firewood is not a tidy box. It is irregular, sometimes wet, occasionally frosted, and much of it is round. Each of those traits works against friction on a belt.

Once the slope passes about 30°, gravity starts beating the grip of the belt surface. Round rounds and heavy wet splits slide backward, cleats get overloaded, and your splitter operator ends up kicking pieces off the hopper. Throughput collapses, and the footing around the loading end turns hazardous.

Between 25° and 28°, cleated belts hold wood securely and the conveyor feeds steadily. The shallower end of that window is kinder to wet, heavy hardwood. The steeper end saves footprint when yard space is tight and your wood is dry and mostly split small.

Here is a quick planning table based on belt run.

Belt run

Rise at 25°

Rise at 28°

15 ft

about 6.3 ft

about 7.0 ft

19.6 ft

about 8.3 ft

about 9.2 ft

23 ft

about 9.7 ft

about 10.8 ft

Use these as a sanity check against the published max lift on any machine. If a rated lift looks far above what your angle and belt run can produce, ask how and at what setting that number is reached. Plan your daily work around the 25° to 28° window, and treat the absolute maximum as occasional headroom.

4. Clearance Sizing for Dump Trailers and Stake-Bed Trucks

Loading a vehicle takes two numbers: vertical clearance over the sidewall, and horizontal reach so the discharge sits above the middle of the bed rather than hanging at the edge.

Start with the height of the tallest rail or panel, then add 18 to 24 inches so splits drop clear without clipping the top edge. Next, add half the width of the bed so wood lands near the center. Most firewood trucks and trailers load best when the wood falls into the middle third.

· Tall-sided dump trailers and dump bodies can run 6 to 7 feet at the rim, and a discharge height of 8.5 to 9 feet clears them with margin. A 10.3-foot machine like the HC2016 sits comfortably there, though sidewall heights vary a lot, so measure your own trailer before you buy.

· Stake-bed trucks with high rails often need 9 to 10 feet of clearance once you add the drop margin. A 15-foot rated lift lets you keep the belt in the 25° to 28° window while still reaching over those rails, and that is where the MechMaxx HC2320 heavy-duty conveyor earns its spot.

· Short flatbeds and utility trailers need the least height, and they pair well with the HC2016's low 60-inch minimum, which makes loading small trailers gentler on the wood.

If your trailer fleet is mixed, size for the tallest unit you load most often. A machine a foot too short makes every load frustrating. One a foot too tall only costs you a little yard space.

Buyers sorting through the heavier models can browse the Heavy Duty Conveyor collection to compare belt widths and lift ranges side by side.

Side and plan diagram showing conveyor discharge clearing a dump trailer rim and landing centered.

5. Conical Woodpile Storage: Cords per Drop

Stockpiling split wood to season? Discharge height decides how long you can run before the machine has to move.

Loosely thrown firewood settles into a cone. With a simple 45° angle of repose, a cone's radius roughly equals its height, and its volume is about one-third of π times height cubed. That cubed term tells the whole story, because a modest gain in height produces a big jump in volume.

· At 10.3 feet, the geometric cone holds about 1,100 cubic feet. In real yards, the conveyor body, uneven throwing, and a pile that never quite forms a perfect cone cut that down, so plan on about 3 to 4 loose cords from a single position.

· At 15 feet, the same math gives roughly three times the volume, since 15 feet is about 1.46 times taller and volume scales with the cube. Real-world planning figures land around 10 to 12 loose cords per position.

The payoff is time. A commercial operation producing several cords a day will keep repositioning a shorter machine, while a taller one lets a splitter run a full shift on one footprint. A homeowner putting up five or six cords for winter will find a 10.3-foot pile plenty, and a smaller machine is easier to tow, store, and maneuver.

Loose cords settle as the wood dries and as you stack down, so these figures describe the pile as it forms. Use them for planning, not as guarantees.

6. Power and Hydraulic Drive Sizing

Both conveyors run a hydraulic belt drive powered by a dedicated gasoline engine, so they work anywhere without borrowing hydraulics from a processor or tractor. On a wood lot with no power and no PTO, that is a real convenience.

The HC2016 pairs its 7HP 212cc Ducar engine with a 5.7 GPM single-stage pump, a 4.2-gallon hydraulic tank running AW-46 fluid, and a 10-micron oil filter. That moves a 16-inch belt loaded with typical split sizes at a steady pace all day. It rolls on 19-inch radial tires mounted on 13-inch rims, with a 2-inch coupler tow bar, is rated for towing up to 45 MPH, and its powder-coated finish stands up to bark, sap, and weather. At 992 pounds, you tow it behind a truck or an ATV, and it repositions quickly once hitched.

The HC2320 steps up to a 9HP 270cc Ducar engine with recoil start and adds hydraulic height adjustment, so you raise and lower the discharge from the operator position instead of fiddling by hand. The wider 19.7-inch belt carries bigger splits and more wood per pass. The extra torque helps when the wood is wet and heavy and the belt runs 23 feet.

If a splitter is already part of the plan, a bundled setup saves matching headaches. The KT34 HC2016 combo pairs a 34-ton kinetic splitter with the HC2016 conveyor, so the splitter drops wood straight onto the belt and the pile builds itself.

Browsing the full firewood conveyor collection is a good way to see how each size compares once you know your target height.

Which Buyer Fits Which Machine

A homeowner or part-time seller who moves a few dozen cords a year, loads a standard trailer, and wants something simple to tow and store will find the HC2016 the practical pick. Its 10.3-foot discharge handles most piles and trailers, and the 60-inch minimum keeps low stacking easy.

A full-time firewood business filling stake-bed delivery trucks, building large seasoning piles, or splitting wide, heavy rounds needs the HC2320. The extra 5 feet of lift separates loading a tall truck at a comfortable slope from fighting a steep one.

Somewhere in the middle? Measure your tallest vehicle, add the drop margin, and let that number choose for you.

7. FAQs

1. What minimum lift height is needed to load high-sided dump trailers or stake-bed trucks?

For tall-sided dump trailers, aim for a discharge height around 8.5 to 9 feet so wood clears the rim with a margin. For stake-bed trucks with high rails, a 12 to 15-foot rated lift gives you room to stay in the 25° to 28° window while reaching over the top.

2. How many cords can a single pile hold before the conveyor has to move?

Real-world planning figures are about 3 to 4 loose cords at a 10.3-foot discharge height and about 10 to 12 loose cords at 15 feet. The geometry is generous, but the conveyor body and uneven throwing trim the usable volume.

3. How do you choose between the HC2016 and HC2320?

Choose by the tallest vehicle or pile you will build. The HC2016 covers residential work and standard trailers with a 7HP engine and 124-inch lift. The HC2320 suits high stake beds and commercial volume with a 9HP engine, 19.7-inch belt, and 180-inch lift.

4. Why must the incline stay between 25° and 28°?

Past roughly 30°, gravity overcomes the grip of the belt and round or wet splits start sliding backward. Staying in the 25° to 28° window keeps wood moving up steadily and keeps the operator at the hopper safe.

5. Does a longer belt always mean a taller discharge?

No. Discharge height depends on the belt run, the working angle, and the frame geometry. Compare the rated maximum discharge height, and use the sine rule to check that your site can support the angle you need.

Next article Previous article

Customer Reviews (0 reviews)